200字范文 > Linux移植5.4版本内核：正点原子阿尔法IMX6ULL开发板Linux内核源码移植详细步骤（5.4

Linux移植5.4版本内核：正点原子阿尔法IMX6ULL开发板Linux内核源码移植详细步骤（5.4

时间：2024-06-09 16:43:54

Linux移植5.4版本内核：正点原子阿尔法IMX6ULL开发板Linux内核源码移植详细步骤（5.4版本内核）

文章目录

Linux移植5.4版本内核：正点原子阿尔法IMX6ULL开发板Linux内核源码移植详细步骤（5.4版本内核）1.出厂源码编译1 修改顶层 Makefile2 配置并编译 Linux 内核3 Linux 内核启动测试 2、移植linux内核,建立单板3.驱动修改1.修改设备树修改前imx6ul-14x14-evk.dtsiimx6ull-14x14-evk.dtsimx6ul-14x14-evk-emmc.dts 修改后imx6ull-alientek.dtsiimx6ull-alientek.dtsimx6ull-alientek-emmc.dts 2 修改网络驱动代码1、修改 fec_main.c 文件2、修改 smsc.c 文件 4.结果1.成功进入内核2.网络检查3.版本信息

nxp出厂Linux源码

/download/weixin_52849254/87666595

移植成功后的Linux源码

/download/weixin_52849254/87669505

NXP 提供的 Linux 源码肯定是可以在自己的 I.MX6ULL EVK 开发板上运行下去的，所以我们肯定是以 I.MX6ULL EVK 开发板为参考，然后将 Linux 内核移植到 I.MX6U-ALPHA 开发板上的。

下载内核

下载地址/Freescale/linux-fslc

Freescale/linux-fslc: Linux kernel source tree ()

/Freescale/linux-fslc/tree/5.4-2.2.x-imx

解压

git clone /Freescale/linux-fslc.gitmkdir fs_5.4unzip linux-fslc-5.4-2.2.x-imx.zip -d fs_5.4/

1.出厂源码编译

1 修改顶层 Makefile

修改顶层 Makefile，直接在顶层 Makefile 文件里面定义 ARCH 和 CROSS_COMPILE 这两个的变量值为 arm 和 arm-linux-gnueabihf-，结果如图所示：

vi Makefile

360 ARCH ?= arm361 CROSS_COMPILE ?= arm-linux-gnueabihf-

或者（用这种）

export ARCH=armexport CROSS_COMPILE=arm-linux-gnueabihf-

第 360 和 361 行分别设置了 ARCH 和 CROSS_COMPILE 这两个变量的值，这样在编译的时候就不用输入很长的命令了。

2 配置并编译 Linux 内核

和 uboot 一样，在编译 Linux 内核之前要先配置 Linux 内核。每个板子都有其对应的默认配置文件，这些默认配置文件保存在 arch/arm/configs 目录中。 imx_v7_defconfig 和imx_v7_mfg_defconfig 都可作为 I.MX6ULL EVK 开发板所使用的默认配置文件。但是这里建议使用 imx_v7_mfg_defconfig 这个默认配置文件，首先此配置文件默认支持 I.MX6UL 这款芯片，而且重要的一点就是此文件编译出来的 zImage 可以通过 NXP 官方提供的 MfgTool 工具烧写！！imx_v7_mfg_defconfig 中的“mfg”的意思就是 MfgTool

进入到 Ubuntu 中的 Linux 源码根目录下，执行如下命令配置 Linux 内核：

make clean //第一次编译 Linux 内核之前先清理一下

查看arch/arm/configs目录下imx6ull相关的单板：

ls arch/arm/configs/ | grep imx

make imx_v7_defconfig //配置 Linux 内核

配置完成以后如图所示：

配置完成以后就可以编译了，使用如下命令编译 Linux 内核：

编译之前先确定安装了libssl-dev 软件包

sudo apt install libssl-dev

make -j32 //编译 Linux 内核

等待编译完成，结果如图所示：

Linux 内核编译完成以后会在 arch/arm/boot 目录下生成 zImage 镜像文件，如果使用设备树的话还会在 arch/arm/boot/dts 目录下开发板对应的.dtb(设备树)文件，比如 imx6ull-14x14-evk.dtb就是 NXP 官方的 I.MX6ULL EVK 开发板对应的设备树文件。至此我们得到两个文件：

①、 Linux 内核镜像文件： zImage。

②、 NXP 官方 I.MX6ULL EVK 开发板对应的设备树文件： imx6ull-14x14-evk.dtb。

3 Linux 内核启动测试

在上一小节我们已经得到了 NXP 官方 I.MX6ULL EVK 开发板对应的 zImage 和 imx6ull-14x14-evk.dtb 这两个文件。这两个文件能不能在正点原子的 I.MX6U-ALPHA EMMC 版开发板上启动呢？测试一下不就知道了，在测试之前确保 uboot 中的环境变量 bootargs 内容如下：

setenv bootargs 'console=tty1 console=ttymxc0,115200 root=/dev/nfs nfsroot=192.168.10.100:/home/alientek/linux/nfs/rootfs,proto=tcp rw ip=192.168.10.101:192.168.10.100:192.168.10.1:255.255.255.0::eth0:off'

将上一小节编译出来的 zImage 和 imx6ull-14x14-evk.dtb 复制到 Ubuntu 中的 tftp 目录下，因为我们要在uboot 中使用 tftp 命令将其下载到开发板中，拷贝命令如下：

cp arch/arm/boot/zImage /home/alientek/linux/tftp/ -fcp arch/arm/boot/dts/imx6ull-14x14-evk.dtb /home/alientek/linux/tftp/ -f

拷贝完成以后就可以测试了，启动开发板，进入 uboot 命令行模式，然后输入如下命令将zImage 和 imx6ull-14x14-evk.dtb 下载到开发板中并启动：

tftp 80800000 zImagetftp 83000000 imx6ull-14x14-evk.dtbbootz 80800000 - 83000000

结果图所示：

2、移植linux内核,建立单板

（1）新建单板配置文件进入 arch/arm/configs 目录，复制一份新的单板文件：

cp arch/arm/configs/imx_v7_defconfig arch/arm/configs/imx_alientek_emmc_defconfig

（2）新建设备树文件进入 arch/arm/boot/dts 目录，复制一份新的设备树文件：

cp aimx6ull-14x14-evk-emmc.dts imx6ull-alientek-emmc.dts

复制并修改依赖

查看该文件，依赖于evk板子的设备树，需要将该文件也复制一份出来：

cp imx6ull-14x14-evk.dts imx6ull-alientek.dts

再查看有没有依赖，竟然还有一级：

5 /dts-v1/;6 7 #include "imx6ull.dtsi"8 #include "imx6ul-14x14-evk.dtsi"

修改依赖：

将该文件也复制一份出来：

cp imx6ul-14x14-evk.dtsi imx6ull-alientek.dtsi

接着修改同级目录下的Makefile，添加新建的文件：

vi Makefile

610 dtb-$(CONFIG_SOC_IMX6UL) += 611imx6ul-14x14-evk.dtb 612imx6ul-14x14-evk-csi.dtb 613imx6ul-14x14-evk-emmc.dtb 614imx6ul-14x14-evk-btwifi.dtb 615imx6ul-14x14-evk-btwifi-oob.dtb 616imx6ul-14x14-evk-ecspi-slave.dtb 617imx6ul-14x14-evk-ecspi.dtb 618imx6ul-14x14-evk-gpmi-weim.dtb 619imx6ul-9x9-evk.dtb 620imx6ul-9x9-evk-ldo.dtb 621imx6ul-9x9-evk-btwifi.dtb 622imx6ul-9x9-evk-btwifi-oob.dtb 623imx6ul-ccimx6ulsbcexpress.dtb 624imx6ul-ccimx6ulsbcpro.dtb 625imx6ul-geam.dtb 626imx6ul-isiot-emmc.dtb 627imx6ul-isiot-nand.dtb 628imx6ul-kontron-n6310-s.dtb 629imx6ul-kontron-n6310-s-43.dtb 630imx6ul-liteboard.dtb 631imx6ul-opos6uldev.dtb 632imx6ul-pico-hobbit.dtb 633imx6ul-pico-pi.dtb 634imx6ul-phytec-segin-ff-rdk-nand.dtb 635imx6ul-tx6ul-0010.dtb 636imx6ul-tx6ul-0011.dtb 637imx6ul-tx6ul-mainboard.dtb 638imx6ull-14x14-evk.dtb 639imx6ull-alientek.dtb 640imx6ull-alientek-emmc.dtb 641imx6ull-14x14-evk-emmc.dtb 642imx6ull-14x14-evk-btwifi.dtb 643imx6ull-14x14-evk-btwifi-oob.dtb 644imx6ull-14x14-evk-gpmi-weim.dtb 645imx6ull-9x9-evk.dtb 646imx6ull-9x9-evk-ldo.dtb 647imx6ull-9x9-evk-btwifi.dtb 648imx6ull-9x9-evk-btwifi-oob.dtb 649imx6ull-colibri-eval-v3.dtb 650imx6ull-colibri-wifi-eval-v3.dtb 651imx6ull-phytec-segin-ff-rdk-nand.dtb 652imx6ull-phytec-segin-ff-rdk-emmc.dtb 653imx6ull-phytec-segin-lc-rdk-nand.dtb 654imx6ulz-14x14-evk.dtb 655imx6ulz-14x14-evk-btwifi.dtb 656imx6ulz-14x14-evk-gpmi-weim.dtb 657imx6ulz-14x14-evk-emmc.dtb

639，640行

（3）编译测试

make distcleanmake imx_alientek_emmc_defconfigmake

复制

cp arch/arm/boot/zImage /home/alientek/linux/tftp/ -fcp arch/arm/boot/dts/imx6ull-alientek-emmc.dtb /home/alientek/linux/tftp/ -f

拷贝完成以后就可以测试了，启动开发板，进入 uboot 命令行模式，然后输入如下命令将zImage 和 imx6ull-14x14-evk.dtb 下载到开发板中并启动：

tftp 80800000 zImagetftp 83000000 imx6ull-alientek-emmc.dtbbootz 80800000 - 83000000

使用新的内核和设备树启动，方便起见，设个环境变量，下次直接用命令启动：

setenv bootcmd 'tftp 80800000 zImage;tftp 83000000 imx6ull-alientek-emmc.dtb;bootz 80800000 - 83000000'saveenv

3.驱动修改

1.修改设备树

修改前

imx6ul-14x14-evk.dtsi

// SPDX-License-Identifier: GPL-2.0//// Copyright (C) Freescale Semiconductor, Inc./ {chosen {stdout-path = &uart1;};memory@80000000 {device_type = "memory";reg = <0x80000000 0x20000000>;};reserved-memory {#address-cells = <1>;#size-cells = <1>;ranges;linux,cma {compatible = "shared-dma-pool";reusable;size = <0xa000000>;linux,cma-default;};};backlight_display: backlight-display {compatible = "pwm-backlight";pwms = <&pwm1 0 5000000>;brightness-levels = <0 4 8 16 32 64 128 255>;default-brightness-level = <6>;status = "okay";};pxp_v4l2 {compatible = "fsl,imx6ul-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2";status = "okay";};reg_sd1_vmmc: regulator-sd1-vmmc {compatible = "regulator-fixed";regulator-name = "VSD_3V3";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;off-on-delay-us = <20000>;enable-active-high;};reg_can_3v3: regulator-can-3v3 {compatible = "regulator-fixed";regulator-name = "can-3v3";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;};sound {compatible = "simple-audio-card";simple-audio-card,name = "mx6ul-wm8960";simple-audio-card,format = "i2s";simple-audio-card,bitclock-master = <&dailink_master>;simple-audio-card,frame-master = <&dailink_master>;simple-audio-card,widgets ="Microphone", "Mic Jack","Line", "Line In","Line", "Line Out","Speaker", "Speaker","Headphone", "Headphone Jack";simple-audio-card,routing ="Headphone Jack", "HP_L","Headphone Jack", "HP_R","Speaker", "SPK_LP","Speaker", "SPK_LN","Speaker", "SPK_RP","Speaker", "SPK_RN","LINPUT1", "Mic Jack","LINPUT3", "Mic Jack","RINPUT1", "Mic Jack","RINPUT2", "Mic Jack";status = "disabled";simple-audio-card,cpu {sound-dai = <&sai2>;status = "disabled";};dailink_master: simple-audio-card,codec {sound-dai = <&codec>;clocks = <&clks IMX6UL_CLK_SAI2>;status = "disabled";};};sound-wm8960 {compatible = "fsl,imx6ul-evk-wm8960","fsl,imx-audio-wm8960";model = "wm8960-audio";cpu-dai = <&sai2>;audio-codec = <&codec>;asrc-controller = <&asrc>;codec-master;gpr = <&gpr 4 0x100000 0x100000>;/** hp-det = <hp-det-pin hp-det-polarity>;* hp-det-pin: JD1 JD2 or JD3* hp-det-polarity = 0: hp detect high for headphone* hp-det-polarity = 1: hp detect high for speaker*/hp-det = <3 0>;hp-det-gpios = <&gpio5 4 0>;mic-det-gpios = <&gpio5 4 0>;audio-routing ="Headphone Jack", "HP_L","Headphone Jack", "HP_R","Ext Spk", "SPK_LP","Ext Spk", "SPK_LN","Ext Spk", "SPK_RP","Ext Spk", "SPK_RN","LINPUT2", "Mic Jack","LINPUT3", "Mic Jack","RINPUT1", "Main MIC","RINPUT2", "Main MIC","Mic Jack", "MICB","Main MIC", "MICB","CPU-Playback", "ASRC-Playback","Playback", "CPU-Playback","ASRC-Capture", "CPU-Capture","CPU-Capture", "Capture";};spi4 {compatible = "spi-gpio";pinctrl-names = "default";pinctrl-0 = <&pinctrl_spi4>;status = "okay";pinctrl-assert-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;gpio-sck = <&gpio5 11 0>;gpio-mosi = <&gpio5 10 0>;cs-gpios = <&gpio5 7 0>;num-chipselects = <1>;#address-cells = <1>;#size-cells = <0>;gpio_spi: gpio@0 {compatible = "fairchild,74hc595";gpio-controller;#gpio-cells = <2>;reg = <0>;registers-number = <1>;registers-default = /bits/ 8 <0x57>;spi-max-frequency = <100000>;};};};&clks {assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <786432000>;};&csi {status = "disabled";port {csi1_ep: endpoint {remote-endpoint = <&ov5640_ep>;};};};&i2c2 {clock-frequency = <100000>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_i2c2>;status = "okay";codec: wm8960@1a {#sound-dai-cells = <0>;compatible = "wlf,wm8960";reg = <0x1a>;wlf,shared-lrclk;clocks = <&clks IMX6UL_CLK_SAI2>;clock-names = "mclk";};ov5640: ov5640@3c {compatible = "ovti,ov5640";reg = <0x3c>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_csi1>;clocks = <&clks IMX6UL_CLK_CSI>;clock-names = "csi_mclk";pwn-gpios = <&gpio_spi 6 1>;rst-gpios = <&gpio_spi 5 0>;csi_id = <0>;mclk = <24000000>;mclk_source = <0>;status = "disabled";port {ov5640_ep: endpoint {remote-endpoint = <&csi1_ep>;};};};};&fec1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_enet1>;phy-mode = "rmii";phy-handle = <&ethphy0>;status = "okay";};&fec2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_enet2>;phy-mode = "rmii";phy-handle = <&ethphy1>;status = "okay";mdio {#address-cells = <1>;#size-cells = <0>;ethphy0: ethernet-phy@2 {reg = <2>;micrel,led-mode = <1>;clocks = <&clks IMX6UL_CLK_ENET_REF>;clock-names = "rmii-ref";};ethphy1: ethernet-phy@1 {reg = <1>;micrel,led-mode = <1>;clocks = <&clks IMX6UL_CLK_ENET2_REF>;clock-names = "rmii-ref";};};};&can1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_flexcan1>;xceiver-supply = <&reg_can_3v3>;status = "okay";};&can2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_flexcan2>;xceiver-supply = <&reg_can_3v3>;status = "okay";};&i2c1 {clock-frequency = <100000>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_i2c1>;status = "okay";mag3110@e {compatible = "fsl,mag3110";reg = <0x0e>;position = <2>;};fxls8471@1e {compatible = "fsl,fxls8471";reg = <0x1e>;position = <0>;interrupt-parent = <&gpio5>;interrupts = <0 8>;};};&lcdif {assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_lcdif_dat&pinctrl_lcdif_ctrl>;display = <&display0>;status = "okay";display0: display@0 {bits-per-pixel = <16>;bus-width = <24>;display-timings {native-mode = <&timing0>;timing0: timing0 {clock-frequency = <9200000>;hactive = <480>;vactive = <272>;hfront-porch = <8>;hback-porch = <4>;hsync-len = <41>;vback-porch = <2>;vfront-porch = <4>;vsync-len = <10>;hsync-active = <0>;vsync-active = <0>;de-active = <1>;pixelclk-active = <0>;};};};};&pwm1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_pwm1>;status = "okay";};&pxp {status = "okay";};&qspi {pinctrl-names = "default";pinctrl-0 = <&pinctrl_qspi>;status = "okay";flash0: n25q256a@0 {#address-cells = <1>;#size-cells = <1>;compatible = "micron,n25q256a", "jedec,spi-nor";spi-max-frequency = <29000000>;spi-rx-bus-width = <4>;spi-tx-bus-width = <4>;reg = <0>;};};&sai2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_sai2>;assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,<&clks IMX6UL_CLK_SAI2>;assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <0>, <12288000>;fsl,sai-mclk-direction-output;status = "okay";};&snvs_poweroff {status = "okay";};&snvs_pwrkey {status = "okay";};&sim2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_sim2>;assigned-clocks = <&clks IMX6UL_CLK_SIM_SEL>;assigned-clock-parents = <&clks IMX6UL_CLK_SIM_PODF>;assigned-clock-rates = <240000000>;/* GPIO_ACTIVE_HIGH/LOW:sim card voltage control* NCN8025:Vcc = ACTIVE_HIGH?5V:3V* TDA8035:Vcc = ACTIVE_HIGH?5V:1.8V*/pinctrl-assert-gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;port = <1>;sven_low_active;status = "okay";};&tsc {pinctrl-names = "default";pinctrl-0 = <&pinctrl_tsc>;xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;measure-delay-time = <0xffff>;pre-charge-time = <0xfff>;status = "okay";};&uart1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_uart1>;status = "okay";};&uart2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_uart2>;uart-has-rtscts;/* for DTE mode, add below change *//* fsl,dte-mode; *//* pinctrl-0 = <&pinctrl_uart2dte>; */status = "okay";};&usbotg1 {dr_mode = "otg";pinctrl-names = "default";pinctrl-0 = <&pinctrl_usb_otg1>;status = "okay";};&usbotg2 {dr_mode = "host";disable-over-current;status = "okay";};&usbphy1 {fsl,tx-d-cal = <106>;};&usbphy2 {fsl,tx-d-cal = <106>;};&usdhc1 {pinctrl-names = "default", "state_100mhz", "state_200mhz";pinctrl-0 = <&pinctrl_usdhc1>;pinctrl-1 = <&pinctrl_usdhc1_100mhz>;pinctrl-2 = <&pinctrl_usdhc1_200mhz>;cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;keep-power-in-suspend;wakeup-source;vmmc-supply = <&reg_sd1_vmmc>;status = "okay";};&usdhc2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_usdhc2>;non-removable;keep-power-in-suspend;wakeup-source;status = "okay";};&wdog1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_wdog>;fsl,ext-reset-output;};&iomuxc {pinctrl-names = "default";pinctrl_csi1: csi1grp {fsl,pins = <MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088>;};pinctrl_enet1: enet1grp {fsl,pins = <MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031>;};pinctrl_enet2: enet2grp {fsl,pins = <MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031>;};pinctrl_flexcan1: flexcan1grp{fsl,pins = <MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020>;};pinctrl_flexcan2: flexcan2grp{fsl,pins = <MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020>;};pinctrl_i2c1: i2c1grp {fsl,pins = <MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0>;};pinctrl_i2c2: i2c2grp {fsl,pins = <MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0>;};pinctrl_lcdif_dat: lcdifdatgrp {fsl,pins = <MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79>;};pinctrl_lcdif_ctrl: lcdifctrlgrp {fsl,pins = <MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79/* used for lcd reset */MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79>;};pinctrl_qspi: qspigrp {fsl,pins = <MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1>;};pinctrl_sai2: sai2grp {fsl,pins = <MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059>;};pinctrl_pwm1: pwm1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0>;};pinctrl_sim2: sim2grp {fsl,pins = <MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008>;};pinctrl_spi4: spi4grp {fsl,pins = <MX6UL_PAD_BOOT_MODE0__GPIO5_IO10 0x70a1MX6UL_PAD_BOOT_MODE1__GPIO5_IO11 0x70a1MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x70a1MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x80000000>;};pinctrl_tsc: tscgrp {fsl,pins = <MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0>;};pinctrl_uart1: uart1grp {fsl,pins = <MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1>;};pinctrl_uart2: uart2grp {fsl,pins = <MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1>;};pinctrl_uart2dte: uart2dtegrp {fsl,pins = <MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX 0x1b0b1MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX 0x1b0b1MX6UL_PAD_UART3_RX_DATA__UART2_DTE_CTS 0x1b0b1MX6UL_PAD_UART3_TX_DATA__UART2_DTE_RTS 0x1b0b1>;};pinctrl_usb_otg1: usbotg1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059>;};pinctrl_usdhc1: usdhc1grp {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10071MX6UL_PAD_SD1_DATA0__USDHC1_DATA00x17059MX6UL_PAD_SD1_DATA1__USDHC1_DATA10x17059MX6UL_PAD_SD1_DATA2__USDHC1_DATA20x17059MX6UL_PAD_SD1_DATA3__USDHC1_DATA30x17059MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */>;};pinctrl_usdhc1_100mhz: usdhc1grp100mhz {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD0x170b9MX6UL_PAD_SD1_CLK__USDHC1_CLK0x100b9MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9>;};pinctrl_usdhc1_200mhz: usdhc1grp200mhz {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD0x170f9MX6UL_PAD_SD1_CLK__USDHC1_CLK0x100f9MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9>;};pinctrl_usdhc2: usdhc2grp {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x17059MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x17059MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059>;};pinctrl_usdhc2_8bit: usdhc2grp_8bit {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x10069MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x17059MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059>;};pinctrl_usdhc2_8bit_100mhz: usdhc2grp_8bit_100mhz {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x100b9MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x170b9MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9>;};pinctrl_usdhc2_8bit_200mhz: usdhc2grp_8bit_200mhz {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x100f9MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x170f9MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9>;};pinctrl_wdog: wdoggrp {fsl,pins = <MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0>;};};

imx6ull-14x14-evk.dts

// SPDX-License-Identifier: (GPL-2.0 OR MIT)//// Copyright (C) Freescale Semiconductor, Inc./dts-v1/;#include "imx6ull.dtsi"#include "imx6ul-14x14-evk.dtsi"/ {model = "Freescale i.MX6 ULL 14x14 EVK Board";compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";};&clks {assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>,<&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <320000000>, <786432000>;};&csi {status = "okay";};&ov5640 {status = "okay";};/delete-node/ &sim2;

imx6ul-14x14-evk-emmc.dts

Copyright NXPThis program is free software; you can redistribute it and/ormodify it under the terms of the GNU General Public Licenseas published by the Free Software Foundation; either version 2of the License, or (at your option) any later version.

#include “imx6ul-14x14-evk.dts”

&usdhc2 {

pinctrl-names = “default”, “state_100mhz”, “state_200mhz”;

pinctrl-0 = <&pinctrl_usdhc2_8bit>;

pinctrl-1 = <&pinctrl_usdhc2_8bit_100mhz>;

pinctrl-2 = <&pinctrl_usdhc2_8bit_200mhz>;

bus-width = <8>;

non-removable;

status = “okay”;

};

修改后

imx6ull-alientek.dtsi

// SPDX-License-Identifier: GPL-2.0//// Copyright (C) Freescale Semiconductor, Inc./ {chosen {stdout-path = &uart1;};memory@80000000 {device_type = "memory";reg = <0x80000000 0x20000000>;};reserved-memory {#address-cells = <1>;#size-cells = <1>;ranges;linux,cma {compatible = "shared-dma-pool";reusable;size = <0xa000000>;linux,cma-default;};};backlight_display: backlight-display {compatible = "pwm-backlight";pwms = <&pwm1 0 5000000>;brightness-levels = <0 4 8 16 32 64 128 255>;default-brightness-level = <7>;status = "okay";};pxp_v4l2 {compatible = "fsl,imx6ul-pxp-v4l2", "fsl,imx6sx-pxp-v4l2", "fsl,imx6sl-pxp-v4l2";status = "okay";};reg_sd1_vmmc: regulator-sd1-vmmc {compatible = "regulator-fixed";regulator-name = "VSD_3V3";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;//gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;off-on-delay-us = <20000>;enable-active-high;};reg_can_3v3: regulator-can-3v3 {compatible = "regulator-fixed";regulator-name = "can-3v3";regulator-min-microvolt = <3300000>;regulator-max-microvolt = <3300000>;//gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;};sound {compatible = "simple-audio-card";simple-audio-card,name = "mx6ul-wm8960";simple-audio-card,format = "i2s";simple-audio-card,bitclock-master = <&dailink_master>;simple-audio-card,frame-master = <&dailink_master>;simple-audio-card,widgets ="Microphone", "Mic Jack","Line", "Line In","Line", "Line Out","Speaker", "Speaker","Headphone", "Headphone Jack";simple-audio-card,routing ="Headphone Jack", "HP_L","Headphone Jack", "HP_R","Speaker", "SPK_LP","Speaker", "SPK_LN","Speaker", "SPK_RP","Speaker", "SPK_RN","LINPUT1", "Mic Jack","LINPUT3", "Mic Jack","RINPUT1", "Mic Jack","RINPUT2", "Mic Jack";status = "disabled";simple-audio-card,cpu {sound-dai = <&sai2>;status = "disabled";};dailink_master: simple-audio-card,codec {sound-dai = <&codec>;clocks = <&clks IMX6UL_CLK_SAI2>;status = "disabled";};};sound-wm8960 {compatible = "fsl,imx6ul-evk-wm8960","fsl,imx-audio-wm8960";model = "wm8960-audio";cpu-dai = <&sai2>;audio-codec = <&codec>;asrc-controller = <&asrc>;codec-master;gpr = <&gpr 4 0x100000 0x100000>;/** hp-det = <hp-det-pin hp-det-polarity>;* hp-det-pin: JD1 JD2 or JD3* hp-det-polarity = 0: hp detect high for headphone* hp-det-polarity = 1: hp detect high for speaker*/hp-det = <3 0>;/* hp-det-gpios = <&gpio5 4 0>;mic-det-gpios = <&gpio5 4 0>; */audio-routing ="Headphone Jack", "HP_L","Headphone Jack", "HP_R","Ext Spk", "SPK_LP","Ext Spk", "SPK_LN","Ext Spk", "SPK_RP","Ext Spk", "SPK_RN","LINPUT2", "Mic Jack","LINPUT3", "Mic Jack","RINPUT1", "Main MIC","RINPUT2", "Main MIC","Mic Jack", "MICB","Main MIC", "MICB","CPU-Playback", "ASRC-Playback","Playback", "CPU-Playback","ASRC-Capture", "CPU-Capture","CPU-Capture", "Capture";};spi4 {compatible = "spi-gpio";pinctrl-names = "default";pinctrl-0 = <&pinctrl_spi4>;status = "okay";/* pinctrl-assert-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; */gpio-sck = <&gpio5 11 0>;gpio-mosi = <&gpio5 10 0>;/* cs-gpios = <&gpio5 7 0>; */num-chipselects = <1>;#address-cells = <1>;#size-cells = <0>;gpio_spi: gpio@0 {compatible = "fairchild,74hc595";gpio-controller;#gpio-cells = <2>;reg = <0>;registers-number = <1>;registers-default = /bits/ 8 <0x57>;spi-max-frequency = <100000>;};};};&clks {assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <786432000>;};&csi {status = "disabled";port {csi1_ep: endpoint {remote-endpoint = <&ov5640_ep>;};};};&i2c2 {clock-frequency = <100000>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_i2c2>;status = "okay";codec: wm8960@1a {#sound-dai-cells = <0>;compatible = "wlf,wm8960";reg = <0x1a>;wlf,shared-lrclk;clocks = <&clks IMX6UL_CLK_SAI2>;clock-names = "mclk";};ov5640: ov5640@3c {compatible = "ovti,ov5640";reg = <0x3c>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_csi1>;clocks = <&clks IMX6UL_CLK_CSI>;clock-names = "csi_mclk";pwn-gpios = <&gpio_spi 6 1>;rst-gpios = <&gpio_spi 5 0>;csi_id = <0>;mclk = <24000000>;mclk_source = <0>;status = "disabled";port {ov5640_ep: endpoint {remote-endpoint = <&csi1_ep>;};};};/* paranoid FT5406/FT5426 */ft5426: ft5426@38 {compatible = "edt,edt-ft5426","edt,edt-ft5406";reg = <0x38>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_tsc&pinctrl_tsc_reset >; interrupt-parent = <&gpio1>; interrupts = <9 0>; reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; interrupt-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; status = "okay";};gt9147:gt9147@14 {compatible = "goodix,gt9147", "goodix,gt9xx";reg = <0x14>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_tsc&pinctrl_tsc_reset >; interrupt-parent = <&gpio1>; interrupts = <9 0>; reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;interrupt-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; status = "disable"; /* 如果需要改为okay */};/* paranoid sill902x,如果需要HDMI就将status改为okay即可 *//*sii902x: sii902x@39 {compatible = "SiI,sii902x";pinctrl-names = "default";pinctrl-0 = <&pinctrl_sii902x>;interrupt-parent = <&gpio1>;interrupts = <9 IRQ_TYPE_EDGE_FALLING>;irq-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;mode_str = "1280x720M@60";bits-per-pixel = <16>;resets = <&sii902x_reset>;reg = <0x39>;status = "disable"; };*/};&fec1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_enet1&pinctrl_enet1_reset>;phy-mode = "rmii";phy-handle = <&ethphy0>;phy-reset-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;phy-reset-duration = <200>;status = "okay";};&fec2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_enet2&pinctrl_enet2_reset>;phy-mode = "rmii";phy-handle = <&ethphy1>;phy-reset-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;phy-reset-duration = <200>;status = "okay";mdio {#address-cells = <1>;#size-cells = <0>;ethphy0: ethernet-phy@0 {compatible = "ethernet-phy-ieee802.3-c22";smsc,disable-energy-detect;reg = <0>;};ethphy1: ethernet-phy@1 {compatible = "ethernet-phy-ieee802.3-c22";smsc,disable-energy-detect;reg = <1>;};};};&can1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_flexcan1>;xceiver-supply = <&reg_can_3v3>;status = "okay";};&i2c1 {clock-frequency = <100000>;pinctrl-names = "default";pinctrl-0 = <&pinctrl_i2c1>;status = "okay";ap3216c@1e {compatible = "alientek,ap3216c";reg = <0x1e>;}; ap3216c@1e {compatible = "alientek,ap3216c";reg = <0x1e>;};};&lcdif {pinctrl-names = "default";pinctrl-0 = <&pinctrl_lcdif_dat&pinctrl_lcdif_ctrl>;display = <&display0>;status = "okay"; /* 7寸1024*600 */display0: display {bits-per-pixel = <24>;bus-width = <24>;display-timings {native-mode = <&timing0>;timing0: timing0 {clock-frequency = <51200000>;hactive = <1024>;vactive = <600>;hfront-porch = <160>;hback-porch = <140>;hsync-len = <20>;vback-porch = <20>;vfront-porch = <12>;vsync-len = <3>;hsync-active = <0>;vsync-active = <0>;de-active = <1>;pixelclk-active = <0>;};};};/* 4.3寸480*272 *//* display0: display {bits-per-pixel = <24>;bus-width = <24>;display-timings {native-mode = <&timing0>;timing0: timing0 {clock-frequency = <9000000>;hactive = <480>;vactive = <272>;hfront-porch = <5>;hback-porch = <40>;hsync-len = <1>;vback-porch = <8>;vfront-porch = <8>;vsync-len = <1>;hsync-active = <0>;vsync-active = <0>;de-active = <1>;pixelclk-active = <0>;};};};*//* 4.3寸800*480 *//* display0: display {bits-per-pixel = <24>;bus-width = <24>;display-timings {native-mode = <&timing0>;timing0: timing0 {clock-frequency = <31000000>;hactive = <800>;vactive = <480>;hfront-porch = <40>;hback-porch = <88>;hsync-len = <48>;vback-porch = <32>;vfront-porch = <13>;vsync-len = <3>;hsync-active = <0>;vsync-active = <0>;de-active = <1>;pixelclk-active = <0>;};};};*/};&ecspi3 {fsl,spi-num-chipselects = <1>;cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; /* cant't use cs-gpios! */pinctrl-names = "default";pinctrl-0 = <&pinctrl_ecspi3>;status = "okay";spidev: icm20608@0 {compatible = "alientek,icm20608";spi-max-frequency = <8000000>;reg = <0>;}; };&pwm1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_pwm1>;status = "okay";};&pwm3 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_pwm3>;clocks = <&clks IMX6UL_CLK_PWM3>,<&clks IMX6UL_CLK_PWM3>;status = "disable";};&adc1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_adc1>;num-channels = <2>;vref-supply = <&reg_can_3v3>;status = "okay"; };&pxp {status = "okay";};&qspi {pinctrl-names = "default";pinctrl-0 = <&pinctrl_qspi>;status = "okay";flash0: n25q256a@0 {#address-cells = <1>;#size-cells = <1>;compatible = "micron,n25q256a", "jedec,spi-nor";spi-max-frequency = <29000000>;spi-rx-bus-width = <4>;spi-tx-bus-width = <4>;reg = <0>;};};&sai2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_sai2>;assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,<&clks IMX6UL_CLK_SAI2>;assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <0>, <12288000>;fsl,sai-mclk-direction-output;status = "okay";};&snvs_poweroff {status = "okay";};&snvs_pwrkey {status = "okay";};&sim2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_sim2>;assigned-clocks = <&clks IMX6UL_CLK_SIM_SEL>;assigned-clock-parents = <&clks IMX6UL_CLK_SIM_PODF>;assigned-clock-rates = <240000000>;/* GPIO_ACTIVE_HIGH/LOW:sim card voltage control* NCN8025:Vcc = ACTIVE_HIGH?5V:3V* TDA8035:Vcc = ACTIVE_HIGH?5V:1.8V*/pinctrl-assert-gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;port = <1>;sven_low_active;status = "okay";};&tsc {pinctrl-names = "default";pinctrl-0 = <&pinctrl_tsc>;/* xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;*/measure-delay-time = <0xffff>;pre-charge-time = <0xfff>;status = "disable";};&uart1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_uart1>;status = "okay";};&uart3 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_uart3>;status = "okay";};&usbotg1 {dr_mode = "otg";pinctrl-names = "default";pinctrl-0 = <&pinctrl_usb_otg1>;status = "okay";};&usbotg2 {dr_mode = "host";disable-over-current;status = "okay";};&usbphy1 {fsl,tx-d-cal = <106>;};&usbphy2 {fsl,tx-d-cal = <106>;};&usdhc1 {pinctrl-names = "default", "state_100mhz", "state_200mhz";pinctrl-0 = <&pinctrl_usdhc1>;pinctrl-1 = <&pinctrl_usdhc1_100mhz>;pinctrl-2 = <&pinctrl_usdhc1_200mhz>;cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;keep-power-in-suspend;wakeup-source;vmmc-supply = <&reg_sd1_vmmc>;status = "okay";no-1-8-v;};&usdhc2 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_usdhc2>;non-removable;keep-power-in-suspend;wakeup-source;status = "okay";};&wdog1 {pinctrl-names = "default";pinctrl-0 = <&pinctrl_wdog>;fsl,ext-reset-output;};&iomuxc {pinctrl-names = "default";pinctrl_csi1: csi1grp {fsl,pins = <MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088>;};/* paranoid ECSPI */pinctrl_ecspi3: icm20608 {fsl,pins = < MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x10b0 /* CS */MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK 0x10b1 /* SCLK */MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO 0x10b1 /* MISO */MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI 0x10b1 /* MOSI */>;};/* paranoid ADC1_CH1 GPIO1_IO01 */pinctrl_adc1: adc1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0 >;};/* paranoid HDMI RGB */pinctrl_hdmi_dat: hdmidatgrp {/* do not change the pimux vlaue on alpaha and mini board*/fsl,pins = <MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x49MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x49MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x49MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x49MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x49MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x49MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x49MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x49MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x49MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x49MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x49MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x49MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x49MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x49MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x49MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x51MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x49MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x49MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x49 MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x49MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x49MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x49MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x49MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x49>;};/* paranoid HDMI RGB */pinctrl_hdmi_ctrl: hdmictrlgrp {fsl,pins = <MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x49MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x49MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x49MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x49>;};pinctrl_enet1: enet1grp {fsl,pins = <MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x10b0>;};pinctrl_enet2: enet2grp {fsl,pins = <MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x10b0>;};pinctrl_flexcan1: flexcan1grp{fsl,pins = <MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020>;};pinctrl_flexcan2: flexcan2grp{fsl,pins = </* MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 */>;};pinctrl_i2c1: i2c1grp {fsl,pins = <MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0>;};pinctrl_i2c2: i2c2grp {fsl,pins = <MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0>;};pinctrl_lcdif_dat: lcdifdatgrp {fsl,pins = <MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x49MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x49MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x49MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x49MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x49MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x49MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x49MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x49MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x49MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x49MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x49MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x49MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x49MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x49MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x49MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x49MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x49MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x49MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x49MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x49MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x49MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x49MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x49MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x49>;};pinctrl_lcdif_ctrl: lcdifctrlgrp {fsl,pins = <MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x49MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x49MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x7949MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x49/* used for lcd reset */MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x49>;};/* paranoid SII902X INT*/pinctrl_sii902x: hdmigrp-1 {fsl,pins = </*MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x11*/>;};/* paranoid PWM3 GPIO1_IO04 */pinctrl_pwm3: pwm3grp {fsl,pins = <MX6UL_PAD_GPIO1_IO04__PWM3_OUT 0x110b0>;};/* paranoid ADC1_CH1 GPIO1_IO01 */pinctrl_adc1: adc1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0 >;};pinctrl_qspi: qspigrp {fsl,pins = <MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1>;};pinctrl_sai2: sai2grp {fsl,pins = <MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK 0x17088MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC 0x17088MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA 0x11088MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA 0x11088MX6UL_PAD_JTAG_TMS__SAI2_MCLK 0x17088MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059>;};pinctrl_pwm1: pwm1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0>;};pinctrl_sim2: sim2grp {fsl,pins = <MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008>;};pinctrl_spi4: spi4grp {fsl,pins = <MX6UL_PAD_BOOT_MODE0__GPIO5_IO10 0x70a1MX6UL_PAD_BOOT_MODE1__GPIO5_IO11 0x70a1/* MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x70a1MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x80000000 */>;};pinctrl_tsc: tscgrp {fsl,pins = </* 7寸RGB屏幕，FT5426 *//* MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0xF080*/ /* TSC_INT *//* 7寸RGB屏幕,GT9147 *//* MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x10B0*/ /* TSC_INT */>;};pinctrl_uart1: uart1grp {fsl,pins = <MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1>;};pinctrl_uart2: uart2grp {fsl,pins = </* MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1 */MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1>;};pinctrl_uart2dte: uart2dtegrp {fsl,pins = </* MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX 0x1b0b1MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX 0x1b0b1MX6UL_PAD_UART3_RX_DATA__UART2_DTE_CTS 0x1b0b1MX6UL_PAD_UART3_TX_DATA__UART2_DTE_RTS 0x1b0b1 */>;};/* paranoid */pinctrl_uart3: uart3grp {fsl,pins = <MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0X1b0b1MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0X1b0b1>;};pinctrl_usb_otg1: usbotg1grp {fsl,pins = <MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059>;};pinctrl_usdhc1: usdhc1grp {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f1MX6UL_PAD_SD1_DATA0__USDHC1_DATA00x17059MX6UL_PAD_SD1_DATA1__USDHC1_DATA10x17059MX6UL_PAD_SD1_DATA2__USDHC1_DATA20x17059MX6UL_PAD_SD1_DATA3__USDHC1_DATA30x17059MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */>;};pinctrl_usdhc1_100mhz: usdhc1grp100mhz {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD0x170b9MX6UL_PAD_SD1_CLK__USDHC1_CLK0x100f1MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9>;};pinctrl_usdhc1_200mhz: usdhc1grp200mhz {fsl,pins = <MX6UL_PAD_SD1_CMD__USDHC1_CMD0x170f9MX6UL_PAD_SD1_CLK__USDHC1_CLK0x100f1MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9>;};pinctrl_usdhc2: usdhc2grp {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x17059MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x17059MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059>;};pinctrl_usdhc2_8bit: usdhc2grp_8bit {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x10069MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x17059MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059>;};pinctrl_usdhc2_8bit_100mhz: usdhc2grp_8bit_100mhz {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x100b9MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x170b9MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170b9MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170b9MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170b9MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170b9>;};pinctrl_usdhc2_8bit_200mhz: usdhc2grp_8bit_200mhz {fsl,pins = <MX6UL_PAD_NAND_RE_B__USDHC2_CLK0x100f9MX6UL_PAD_NAND_WE_B__USDHC2_CMD0x170f9MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9>;};pinctrl_wdog: wdoggrp {fsl,pins = <MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0>;};};&iomuxc_snvs {pinctrl-names = "default_snvs";pinctrl-0 = <&pinctrl_hog_2>;imx6ul-evk {/* zuozhongkai Touch RESET */pinctrl_tsc_reset: tsc_reset {fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x10B0>;};/* zuozhongkai RGB RESET */ts_reset_hdmi_pin: ts_reset_hdmi_mux {fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x49>;};pinctrl_hog_2: hoggrp-2 {fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO000x80000000>;};pinctrl_dvfs: dvfsgrp {fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO030x79>;};pinctrl_lcdif_reset: lcdifresetgrp {fsl,pins = </* used for lcd reset *//* MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79 */>;};pinctrl_sai2_hp_det_b: sai2_hp_det_grp {fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x17059>;};/*enet1 reset zuozhongkai*/pinctrl_enet1_reset: enet1resetgrp {fsl,pins = </* used for enet1 reset */MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO070x10B0/* ENET1 RESET */>;};/*enet2 reset zuozhongkai*/pinctrl_enet2_reset: enet2resetgrp {fsl,pins = </* used for enet2 reset */MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO080x10B0/* ENET2 RESET */>;};};};

imx6ull-alientek.dts

// SPDX-License-Identifier: (GPL-2.0 OR MIT)//// Copyright (C) Freescale Semiconductor, Inc./dts-v1/;#include "imx6ull.dtsi"#include "imx6ull-alientek.dtsi"/ {model = "Freescale i.MX6 ULL 14x14 EVK Board";compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";};&clks {assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>,<&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;assigned-clock-rates = <320000000>, <786432000>;};&csi {status = "okay";};&ov5640 {status = "okay";};/delete-node/ &sim2;

imx6ull-alientek-emmc.dts

#include “imx6ull-alientek.dts”

&usdhc2 {

pinctrl-names = “default”, “state_100mhz”, “state_200mhz”;

pinctrl-0 = <&pinctrl_usdhc2_8bit>;

pinctrl-1 = <&pinctrl_usdhc2_8bit_100mhz>;

pinctrl-2 = <&pinctrl_usdhc2_8bit_200mhz>;

bus-width = <8>;

non-removable;

status = “okay”;

};

2 修改网络驱动代码

Linux 驱动开发的时候要用到网络调试驱动，所以必须要把网络驱动调试好。在讲解 uboot 移植的时候就已经说过了，正点原子开发板的网络和 NXP 官方的网络硬件上不同，网络 PHY 芯片由 KSZ8081 换为了 LAN8720A，两个网络 PHY 芯片的复位 IO 也不同。所以 Linux 内核自带的网络驱动是驱动不起来 I.MX6U-ALPHA 开发板上的网络的，需要做修改。

1、修改 fec_main.c 文件

要在 I.MX6ULL 上使用 LAN8720A ，需要修改一下 Linux 内核源码，打开drivers/net/ethernet/freescale/fec_main.c，找到函数 fec_probe，在 fec_probe 中加入如下代码：

修改前

3438 static int3439 fec_probe(struct platform_device *pdev)3440 {3441struct fec_enet_private *fep;3442struct fec_platform_data *pdata;3443struct net_device *ndev;3444int i, irq, ret = 0;3445struct resource *r;3446const struct of_device_id *of_id;3447static int dev_id;3448struct device_node *np = pdev->dev.of_node, *phy_node;3449int num_tx_qs;3450int num_rx_qs;3451 3452fec_enet_get_queue_num(pdev, &num_tx_qs, &num_rx_qs);3453 3454/* Init network device */3455ndev = alloc_etherdev_mqs(sizeof(struct fec_enet_private),3456 num_tx_qs, num_rx_qs);3457if (!ndev)3458 return -ENOMEM;3459 3460SET_NETDEV_DEV(ndev, &pdev->dev);3461 3462/* setup board info structure */3463fep = netdev_priv(ndev);3464 3465of_id = of_match_device(fec_dt_ids, &pdev->dev);3466if (of_id)3467 pdev->id_entry = of_id->data;3468fep->quirks = pdev->id_entry->driver_data;3469 3470fep->netdev = ndev;3471fep->num_rx_queues = num_rx_qs;。。。。。

修改后

static int3439 fec_probe(struct platform_device *pdev)3440 {3441struct fec_enet_private *fep;3442struct fec_platform_data *pdata;3443struct net_device *ndev;3444int i, irq, ret = 0;3445struct resource *r;3446const struct of_device_id *of_id;3447static int dev_id;3448struct device_node *np = pdev->dev.of_node, *phy_node;3449int num_tx_qs;3450int num_rx_qs;3451 3452/* 设置 MX6UL_PAD_ENET1_TX_CLK 和 MX6UL_PAD_ENET2_TX_CLK3453* 这两个 IO 的复用寄存器的 SION 位为 1。3454*/3455void __iomem *IMX6U_ENET1_TX_CLK;3456void __iomem *IMX6U_ENET2_TX_CLK;3457 3458IMX6U_ENET1_TX_CLK = ioremap(0X020E00DC, 4);3459writel(0X14, IMX6U_ENET1_TX_CLK);3460 3461IMX6U_ENET2_TX_CLK = ioremap(0X020E00FC, 4);3462writel(0X14, IMX6U_ENET2_TX_CLK);3463fec_enet_get_queue_num(pdev, &num_tx_qs, &num_rx_qs);3464 3465/* Init network device */3466ndev = alloc_etherdev_mqs(sizeof(struct fec_enet_private),3467 num_tx_qs, num_rx_qs);3468if (!ndev)3469 return -ENOMEM;34703471SET_NETDEV_DEV(ndev, &pdev->dev);34723473/* setup board info structure */

第 3455~3462 就是新加入的代码，如果要在 I.MX6ULL 上使用 LAN8720A 就需要设置ENET1 和 ENET2 的 TX_CLK 引脚复位寄存器的 SION 位为 1。

2、修改 smsc.c 文件

首先需要找到 LAN8720A 的驱动文件， LAN8720A 的驱动文件是 drivers/net/phy/smsc.c，在此文件中有个叫做 smsc_phy_reset 的函数，看名字都知道这是 SMSC PHY 的复位函数，因此， LAN8720A 肯定也会使用到这个复位函数，修改此函数的内容，修改以后的 smsc_phy_reset函数内容如下所示：

修改前

60 static int smsc_phy_reset(struct phy_device *phydev)61 {62int rc = phy_read(phydev, MII_LAN83C185_SPECIAL_MODES);63if (rc < 0)64 return rc;65 66/* If the SMSC PHY is in power down mode, then set it67* in all capable mode before using it.68*/69if ((rc & MII_LAN83C185_MODE_MASK) == MII_LAN83C185_MODE_POWERDOWN) {70 int timeout = 50000;71 72 /* set "all capable" mode and reset the phy */73 rc |= MII_LAN83C185_MODE_ALL;74 phy_write(phydev, MII_LAN83C185_SPECIAL_MODES, rc);75 phy_write(phydev, MII_BMCR, BMCR_RESET);76 77 /* wait end of reset (max 500 ms) */78 do {79 udelay(10);80 if (timeout-- == 0)81 return -1;82 rc = phy_read(phydev, MII_BMCR);83 } while (rc & BMCR_RESET);84}85return 0;86 }

修改后

static int smsc_phy_reset(struct phy_device *phydev){int err, phy_reset;int msec = 1;struct device_node *np;int timeout = 50000;if(phydev->addr == 0) /* FEC1 */ {np = of_find_node_by_path("/soc/aips-bus@02100000/ethernet@02188000");if(np == NULL) {return -EINVAL;}}if(phydev->addr == 1) /* FEC2 */ {np = of_find_node_by_path("/soc/aips-bus@02000000/ethernet@020b4000");if(np == NULL) {return -EINVAL;} } err = of_property_read_u32(np, "phy-reset-duration", &msec);/* A sane reset duration should not be longer than 1s */if (!err && msec > 1000)msec = 1;phy_reset = of_get_named_gpio(np, "phy-reset-gpios", 0); if (!gpio_is_valid(phy_reset))return;gpio_direction_output(phy_reset, 0); gpio_set_value(phy_reset, 0); msleep(msec);gpio_set_value(phy_reset, 1); int rc = phy_read(phydev, MII_LAN83C185_SPECIAL_MODES);if (rc < 0)return rc; /* If the SMSC PHY is in power down mode, then set it* in all capable mode before using it.*/102if ((rc & MII_LAN83C185_MODE_MASK) == MII_LAN83C185_MODE_POWERDOWN) {103 104 /* set "all capable" mode and reset the phy */105 rc |= MII_LAN83C185_MODE_ALL;106 phy_write(phydev, MII_LAN83C185_SPECIAL_MODES, rc);107 }108 phy_write(phydev, MII_BMCR, BMCR_RESET);109 110 /* wait end of reset (max 500 ms) */111do {112 udelay(10);113 if (timeout-- == 0)114 return -1; 115 rc = phy_read(phydev, MII_BMCR);116} while (rc & BMCR_RESET);117118return 0;119 }

第 7~12 行，获取 FEC1 网卡对应的设备节点。

第 14~19 行，获取 FEC2 网卡对应的设备节点。

第 21 行，从设备树中获取“phy-reset-duration”属性信息，也就是复位时间。

第 25 行，从设备树中获取“phy-reset-gpios”属性信息，也就是复位 IO。

第 29~32 行，设置 PHY 的复位 IO，复位 LAN8720A。

第 41~48 行，以前的 smsc_phy_reset 函数会判断 LAN8720 是否处于 Powerdown 模式，只有处于 Powerdown 模式的时候才会软复位 LAN8720。这里我们将软复位代码移出来，这样每次调用 smsc_phy_reset 函数 LAN8720A 都会被软复位。最后我们还需要在 drivers/net/phy/smsc.c 文件中添加两个头文件，因为修改后的smsc_phy_reset 函数用到了 gpio_direction_output 和 gpio_set_value 这两个函数，需要添加的头文件如下所示：

#include <linux/of_gpio.h>#include <linux/io.h>

然后编译源码，启动开发板