壁面模型,wall model
1)wall model壁面模型
1.Effects of Wall Models on Heat Transfer Multi-dimensional Transient Numerical Simulation in Diesel Cylinder壁面模型对缸内传热多维瞬态数值模拟计算的影响
2.Based on the coherent structures,a new type ofwall model for large-eddy simulation(LES) was established.在此基础上,提出了基于近壁区相干结构流动参数的新型大涡模拟壁面模型。
英文短句/例句
1.Effects of Wall Models on Heat Transfer Multi-dimensional Transient Numerical Simulation in Diesel Cylinder壁面模型对缸内传热多维瞬态数值模拟计算的影响
2.Fuzzy optimal design facing cavity wall thickness of large-scale die casting mold面向大型压铸模型腔壁厚的模糊优化设计
3.Joint measurements of surface pressure fluctuations and near-wall turbulent flow at the etern of an underwater vehicle model水下航行体模型尾部壁面脉动压力与近壁湍动速度同步测试研究
4.Dynamic model of coherent structure by local disturbance in wall region of a turbulent boundary layer近壁湍流边界层壁面局部扰动诱导形成相干结构的动力学模型
5.Establishment of Moving Deformable Barrier Model and Research of Car Side Crashworthiness;移动变形壁障模型建立及汽车侧面耐撞性研究
6.A MATERIAL NONLINEAR FINITE ELEMENT MODEL OF SPATIAL THIN-WALLED BEAMS空间薄壁截面梁的材料非线性有限元模型
7.Evaluation of Numerical Simulation on Discharge Capacity and The Way Used to Track Free-Surface-Taking The Rectangle Sharp-Crested Weir as An Instance数值模型计算泄流能力和模拟自由水面的评价—以薄壁堰流为例
8.Manufacturing process of large scale thin walled part for automotive main model面向汽车匹配主模型检具的大型薄壁件制造工艺
9.Research on Melt Viscosity and Wall-slip in Micro-injection Molding Filling Flow;微注塑成型充模流动中熔体粘度和壁面滑移的研究
10.Surface Processing Treatment and Aberration Control over Slip-Form Construction of Large Silo Wall大型筒仓仓壁滑模施工表面工艺处理及色差控制
11.Numerical simulation of the influences of catalytic wall on methane combustion characteristics in micro-combustor催化壁面对微型燃烧腔内甲烷燃烧影响的数值模拟
parison and research on several wall functions in plane two-dimension k-ε turbulence model平面二维k-ε紊流模型不同壁函数的对比及研究
13.On the basis of analysis of the existing die failure induced by deformation, with the aid of FEM analysis, a typical deformation of die surface was studied.以实际变形失效的模具为基础,借助有限元分析,研究了典型模具型腔壁面上的变形情况。
14.The characteristics of dew condensation in the inner wall and their influence factors were analyzed based on the establishment of physical and mathematical models.本文进一步研究了舱内通风对壁面结露特性的影响,建立了合理的物理模型和数学模型。
15.Equilibrium Configuration Simulation of Single and Double Walled Carbon Nanotubes by Molecular Mechanics;单壁和双壁碳纳米管分子静力学模型研究
16.Study on Thin-Wall and Low-Roughness Ceramic Shell Mould Based on EPS Process薄壁光整消失模壳型铸造的型壳研究
17.formation anomaly simulation trace地层层面与井壁相交的模拟迹线
18.Influence of Different Wall Boundary Conditions on Tunnel Fires Simulation壁面边界条件对隧道火灾模拟的影响
相关短句/例句
wall-film model壁面液膜模型
1.The turbulent flow of gas phase was modeled by the standard k-ε turbulent model, while the liquid flow was based on the Lagrange Discrete Phase Model of multiphase flow,and the behavior of liquid particle on the wall was simulated by awall-film model.计算中气相采用标准k-ε湍流模型,液相采用拉格朗日离散相模型,液滴的壁面行为采用壁面液膜模型。
3)near wall turbulence models壁面湍流模型
4)wall-collision model壁面碰撞模型
5)Particle-wall collision model颗粒-壁面碰撞模型
6)surface of mould cavity型腔壁面
1.The process of mould filling for the flat plastic products with local sunk was investigated; an equation to calculate the side force on core protruding which causes fatigue stress craze onsurface of mould cavity was formulated.研究具有局部凹陷结构的板状制品注塑模具型腔的熔体充模过程,得出导致型腔壁面疲劳应力开裂的型芯凸块侧推力计算公式。
延伸阅读
蒸发面后退模型分子式：CAS号：性质：在非吸附性多孔物料的减速干燥阶段，一般存在干燥区和湿区两部分。物料内部的内部蒸发实际上是在湿区的某处进行。但为了使问题简化起见，把内部蒸发看成仅在干燥区与湿区的交界面上进行，这样的模型即称为蒸发面后退模型。
